Thursday, 9 July 2020

Bottom work en upright again!

Well, where tot start...

The main purpose of turning over the boat was to be able to weld the bottom.
That succeeded so quickly that I didn't take any picture of it. I have a small Youtube of the final touches however: 

Now at the same time I devoloped the idea to coat the bottom as well. When turing the boat boack again I would like to put it on its trailer right away. With a finished bottom I didn't have to move it anymore to coat the hidden spots. 
The Keel I had to keep unpainted however. I still have to pour the ballast and I guess that the hot molten lead would damage the paint on the outside.

In the following pictures I'll give you an impression of the "priming-filling/leveling-coating" of the hull:







As you see I had to "correct" some small deformings. After all they were the first stages I build and I was indeed confronted with my lack of experience back then 😔. 

Still confused wether to label it as "imperfect" or as "not-bad-for-an-amateur".






Monday, 27 April 2020

Rolling over with just 3 men in 1 hour

Time came to turn this vessel up side down as well. Not for covering or painting but to weld the long outside joints of the hull.
Now what to do in a pandemic limited situation? Try to do it all by my self? That would be possible if I had the right machines. 
But with some family and a bit of “engineering” it could do the job within an hour.

I extended the existing cradle over the top side of the boat in such a way that it formed a kind of crate which could be rolled over in a few steps.
Halfway the process I took the wheels from the bottom side and screwed them on the topside. The boat rolled in to the garage as easy as it came out... upside down...



As you can see at the picture above I didn’t finish the dorade boxes yet. This is because I had to leave out the floor boards until after the welding of the hull. Hot spatters could burn and ruin the floor. I can just pass these boards through the vent holes in the forward cabin wall.
















Saturday, 29 February 2020

Roofing with Erik

Hi there.

Today Erik helped me with placing the roof on the cabin.
Erik is my collegue who motivated me to build the pocketship in aluminum.

For this the boat had to move out of its cramped yard to be able to weld the two roof halfs.
This has to be done inside as wind is going well with making a good weld.
Nice oportunity for taking some pictures however...


As you see I did not add the dorade boxes yet. That is because I have to enter the floor boards through the inner openings of the vents. I have these still outside the boat becaus I have to weld the bottom still and I don't want to burn the floor boards with the hot welding splatters.

And what do you think of my rudder...

Saturday, 22 February 2020

Time for a new post

Hi there,

Been a while again but good news, I was busy with building rather than blogging 😀.
And yes I passed my welding exam and yes I learned a lot again while building.

As this design is well constructed and I guess drawn in a CAD program all the parts should fit like a glove. In a wooden version a gap of an extra milimeter or 2-4 is not a problem as you dab an extra dot of epoxy with filler to solve it. For welding it is important to have no gaps at all as that is the easyest way of welding.

So I learned 2 important skills: Bending and filling.
When to parts aren't fitting that means that the curve of the panels isn't right yet. But with these fish-like shapes it takes a while to find out where to bend (or stretch) in order to close a gap. And sometimes you have to bend a panel about two meters aft (or forward) from the gap. Now with a bit of experience I now am able to make the panels fit quite accurately. And - not a surprize of course - it smooths the curves of the hull as well.

Second skill is fillet-welding. Once I found the right settings for my welding machine for the various positions I was able to close the remaining small gaps with a fillet-weld. This gives me more confidence to get the vessel watertight after all 💦😂.

In the pictures below I'll show you some stages of the deck build up from the past few weeks.

Picture right: I was extremely satisfied that I was able to shape the bow section smoothly. I used the deck template for the right curves and it took some timber to get there. Aluminum doesn't react the same as wood and it didn't follow a smooth curve around the bulkheads. In particularly after I welded the bulkheads the panels waved in stead of following a smooth curve due to heath schrinkage.

In the cockpit and cabin area it was quite easy to make the panels fit. I allready spread the sides to fit the seat panels and just a last milimeter was needed to close all the gaps between the lower and the upper side panels. (picture below)



 Rest of the pictures is about building up the backrests and the aft cabin wall:



And final result of the transom made with a 22 mm aluminum tube:




Tuesday, 26 November 2019

New phase

Last months I was very busy preparing for two exams both after about a year of training.
First of all I am officially a First Aid Instructor now. Happy to have passed that exam. Not as easy as I expected and a few organizations depended on me getting this certificate.

2nd and ofcourse the most interesting one my first official NIL welding certificate TIG (GTAW) Aluminum. I passed the practical exam and I trust I passed the theoretical as well but I'll have to await the official message.

So... A big black hole (time warp) ending study activities and time for the next phase in building the first Aluminum pocketship.

I cut the top pieces of the paterns and will make some templates in a few days.
I try to order the next set of sheet aluminum before Christmas holidays so that I will be able to do some cutting and welding between "Turkey and Fireworks".



Wednesday, 23 October 2019

Too busy to build but there is some progress...

Sorry to say but I really was a bit too busy to do much on the boat.
As ever I do multiple courses. Still doing welding courses and an Instructor First Aid course.
Well, during exam times there's not much time left unfortunately.

But I couldn't resist to do some boatbuilding every now and then 😏.
Here are some pictures of the progress:


In these pictures I finished the bulkheads and the floor frames. I bended the floor frames to have some platform to fix the wooden floor. I discovered that it is much more precise not to do that but to weld a piece of L-profile instead. I can line up these pieces exactly. Now I have to correct the height with some filler pieces of wood. Not a big problem but extra work.


Bulkhead 7 is in the wood version a complet closed bulkhead which has to be cut out after installing. This is a very inefficient way in aluminum. In a next build I won't do this again. An L-profile crossbar, an extra floor frame and the cut out piece of bulkhead 8 will do the job perfectly I guess.

I also started the floor of the cabin. Working with wood again yeah... 




I absolutely enjoyed this. Took about a half day of work. Still have to finish the wood of course. Not sure how to treat the floor boards. Varnish? Tung Oil? something else?

Friday, 9 August 2019

Learning, learning, learning, deforming and welding process...

You can't imagine: my fulltime job is in (higher) education and I never learned so much as with this project...

Ok, that was to be expected for the good reasons that I am an unexperienced welder and that I try to build an intended wooden boat in aluminum 😎 but hey, would Columbus ever had discovered Turtle Island without trying "something else"?

In fact there is so much to tell that I don’t know where to start. All metals including aluminum deforms when heated. They tell you a very limited amount about it during welding classes, nothing about the size of a boat. So I have to learn my lessons during building-time and I can tell you: these lessons are very very interesting. I already experienced these phenomena with the centerboard-trunk but after that every weld caused its troubles. It troubled me a lot. Did I choose the right welding method? Did I really bought the wrong welding machine? Did I really do the wrong welding course?

Now a few weeks later I know the answer and of course as ever it is “yes and no”.
Why do most of the aluminum boat builders use the MIG welding process? Not because of the advantages of TIG but of the disadvantages ofcourse. First of all and most im portant the heath transfer. TIG is a slower process and adds more heath into the metal than MIG. The difference is not only significant but humendous (as I experienced). Second - I thought not very important - is that MIG welds with only one hand. In fact this has two important advantages: first you can hold the pieces into place while (tack)welding with the other hand. Turned out to be very very very handy. And second the “agility”. Single hand welding also means welding in narrow spaces, easy welding in all positions and welding left and right handed!



You guessed already I had to switch to MIG. Fortunately I could sell my TIG welder fast and for a good price and found a MIG welder with the right specs by my favorite supplier (HBM-machines).

 

Yep this is a professional machine and it’s about the same price as my TIG welder.

Now what about lessons? MIG is completely different from TIG welding. Aluminum-welding is aluminum-welding however. The metal behaves about the same. And the difference between no welding experience at all and some experience is much bigger than than the difference between TIG and MIG. They say that if you start with TIG (as the most difficult proces) you can learn MIG faster and I think that’s true.